If it doesn’t work by default, long press the app, go into app info, scroll to advanced, enable exploit protection compatibility mode.

The floor is made of ground too.

I’d get one if it was like $300 less

I use it on my steam deck microsd to cram more shit in via compression. Main drive is left as ext4 though so case folding can be used for particularly janky windows games or mods.

Do you mean the cat is your mom, or you are the cats mom?

I used Manjaro for several years but it requires so much manual intervention on updates that don’t work. Just straight arch or endeavor would be easier in the long run imo. I use tumbleweed on my current main computer though.

Edit: make sure the wires in the screw terminals on the pcb don’t have solder on the ends. Clip it and strip it to bare wire or put crimped ferrules on the ends. You can get arcing and fire from the solder softening and the wire slipping out.

All metal or bi metal heat break, or just replace the whole hotend with one of those ceramic heater ones.

Printed locking notched bed level wheels. I used one that had a number of teeth to match the rotation suggestions from the klipper screw adjust macro that uses abl to measure how much to turn each one.

Magnet bed plates. I have smooth matte pei, textured pei, gloss peo, unknown generic textured black stuff, and something else I can’t remember. Different filaments work better or worse on different bed materials and get great results without derpy hax like glue stick. I generally do abs on matte and everything else on tex or super smooth.

Printed abl. I use klackender. It calls for jap omron mouse click switch but I used kailh gm8 as a drop in replacement and it works great.

After trying pretty much every z mod I went with belted z from same website/discord/git as klackender. Single and dual drive dual rod and pom nut etc all skipped every now and then but now any print problems are from other causes. It’s a bit involved but effort and cost to returns is better ratio compared to the switchwire conversion…

Klipper. You can use basically any computer. I have one on a rpi zero 2 and one with a Dell computer that came with windows but is worse than a bad Chromebook. Both use dietpi as the os and kiauh to set up klipper and mainsail.

Opensuse and a couple other distros I tested can do this too right out of the notification panel which is thankfully easy enough for my parents and grandparents. I still end up using the “quake style terminal” most of the time and just flatpak through the notification sometimes.

I can’t even bring myself to use the gui update tools on distros that have them. It just feels like doing anything with extra weight strapped on to every limb.

In the Intel core 2 era I played with doing this and trying to have the kernel and software all optimized and compiled for the specific hardware of the specific computer I was using and the performance gains if any were negligible.

I’d lean towards no.

My recommendation is check if you have a local ink/toner shop and see what their refill prices are for the toner cartridges. I chose my printers based on being cheap to continually use and the quality is good enough for me.

If I was nearly as in to gaming as I was back in the day I would dust off and raise my jolly old flag.

I regret even seeing this

Is there a description of what this is and what it is for for dumdums? I don’t really get what it is from the website.

There are a few ways I can think of to do this but I’m not sure what would be the best way.

You can just mount individual drives or partitions to the corresponding location (xdg directories or otherwise). This is what I generally do.

I haven’t tried this but If you don’t want to partition the shared drives, you could make corresponding folders on the root of the drive (or anywhere really) and bind mount those folders to the corresponding location. For it to be persistent across reboots, a brief search says you can put it in fstab this way: /source /destination none defaults,bind 0 0 There is also rbind which I think is recursive but I haven’t read up on when to use it.

I haven’t tried this either and forget which is which but symbolic link or hard link may or may not be viable and would also be persistent I think.

Those look excellent. Wish it was possible to email food.

I’m to old to have thought of submitting an ai essay in school lol

This reads like a high school essay made in the absolute last minute before it was due and the kid couldn’t come up with anything worthwhile to write about.

I love wget.

The only printers are brother laser and old models of other brand laser. Everything else is dead to me.